Stage #1: Connection of wire

Connect all wire as indicated on the diagram stuck inside the metal case.

# 2: Connection of the power for the first time & assignment of the keypad 6150.

When you to connect the current in the catch with or without the connected battery, you must hear a beep coming from the keyboard! You must assign the address "16" for your keyboard. With this intention when you hear the beep! you have 60 seconds for press at the same time on keys 1 & 3 during 2 seconds, it will appear "31 then" the address by defect which you must change for "16" while supporting on 1 and 6 then on * and all will disappear.

Wait some second and D1 will appear on your keyboard.

When you see D1 on your keypad this wants to say that you have 60 second to enter the programming while pressinng on "*" and "#" simultaneously during 3 seconds. You should see appearing "20" This wants to say that you are with the option * 20 of the programming. See your installation guide for various stars *.

If you do not see any more D1 and that you want to return there for the programming disconnect all including the battery and replug.

If it does not appear D1 on your keyboard it is that Your connection, your spinnings are badly installed. It can be written OC for error.

Wait until D1 disappears

#4: Enter the programming

Once your keypad programmed you will be able to enter in the programming in all times by pressing 4 1 1 2 8 0 0

4112 is the default programing code and 800 it for entered the programming thus if your code of fitter were 1212 should make you 1 2 1 2 and 8 0 0.

Once entered your code of fitter and 8 0 0 should see you appearing "20" This wants to say that you are with the option * 20 of the programming. See your handbook of installation for various stars *.

#5: To change option once entered the programming and that you voyer "20"

To change option made to you quite simply * the number of option wish and will be to you there. Ex * 56

You must programmed each zone from 1 to 6 and to register what you installed

Example 1 contact principal door - 1 motion detector - 1 door-contact interrupter or window without delay or 1 detector sets fire to. Here codes for standard zones as indicated in your Installation Guide page "5-2"

00 = Not used = nothing - 01 = Entry/exit #1 = Door #1 with deadlines - 02 = Entry/exit #2 = Door #2 with times

03 = Perimeter = instantaneous Contact fenestrates or other carries - 04 Intérior follower = Détecteur of movement

09 = Fire = Detecting fire

Once in the programming press * 5 6 it will not appear anything, press * to advance

you will see "01 then" what wants to say "zone 1" Then you press 2 times on *

It will appear 09 this is your "standard zone" enter good the standard zone Exemple door-contact interrupter of entered #1 to support you on 0 and 1 for standard zone "01"

Then you press on * advancing. Once to press on * should see you "10" This is code for the communication not to change anything with this. To locate you should see you always appearing "10" after the "standard zone"

Then to still press on * for advancing: All will disappear.

Then to still press on * advancing: It will appear "01" This wants to say that you finished the zone "01"

Then to still press on * advancing: All will disappear.

Then to still press on * advancing: It will appear "02" This wants to say that you begin the zone "02"

---

(all starts again) After you press 2 times on *

It will appear 01 this is your "standard zone" enter good the standard zone Exemple door-contact interrupter of entered #2 to presss you on 0 and 2 for standard zone "02"

Then you press on * advancing. Once to support on * should see you "10"

Then to still press on * advancing: All will disappear.

Then to still support on * advancing: It will appear "02" This wants to say that you finished the zone "02"

Then to still press on * advancing: All will disappear.

Then to still press on * advancing: It will appear "03" This wants to say that you begin the zone "03"

And so on.

You must go to a new zone. Example you are in zone 4 to press on * until  05 appears

Then to press on 0 and 0: all will disappear And you will be able to leave the programming while pressing on * 99

Once in the programming, if you do not know any more or you are returned

disconnected the current and the battery and replugged the whole. You should hear a beep! And to see appearing D1 on your keyboard. Then press at the same time on * and # during 2 second. You should see appearing "20"

For all reset to support on * 9 6 should then hear a beep * 97 and another beep to you

and you begin at the first again and  you make for example * 56 if you want to program your zones again.